In the current world of mechanical oil recovery, the most common is the screw pump oil pumping, and its most common operational problems is the pump can not be fully filled, resulting in low productivity, the pump is not fully filled due to the pump capacity is greater than the well production or Pump suction inlet gas separation is not good, part of the pump displacement by the gas interference and loss, if you eliminate the pump gas interference and control the pump running time, so that the pump displacement and flow into the bottom of the liquid volume to match, you can increase efficiency And reduce costs. To maintain the high yield of the screw pump pumping practice as follows: 1, first of all, should be sonic liquid level determination to determine the relative depth of liquid production and pump suction inlet. If the liquid level is higher than the pump inlet, then the well can not be mined at maximum capacity. If the air interference affects the yield, the liquid level is higher than the pump inlet; if the excess pumping leads to low output, the liquid level should be at or near the pump inlet. 2, and then through the dynamometer to measure the percentage of full pump coefficient, the application of integrated data acquisition system can be obtained at the same time motor power and data show. One of the main uses of a dynamometer is to diagnose how the pump is operating and to analyze downhole problems. Applying production level measurements in conjunction with a visualization diagram can tell if the well is producing at maximum throughput, whether the column height is higher than the pump suction port depth, whether the screw pump is incompletely filled, and whether the free gas is moving up the annulus. 3, how to diagnose low energy efficiency wells. The diagnostic method is to determine the total efficiency of the pumping system, and to determine the total efficiency, only the power input to the prime mover, the production pressure at the bottom of the well and the exact production test data are determined. The general beam pumping system, the total efficiency should be about 50%, if lower than this should improve its performance. Technologies that increase overall efficiency include maintaining high volumetric efficiency (pump size matches wellbore injection volume, eliminating gas interference, pumping with an evacuation controller or timer) and replacing an oversized motor. 4, the use of underground gas separation. Invalid screw pump operation is often caused by air interference can be diagnosed by acoustic wave measurement and dynamometer. It is best to place the pump suction below the fluid inlet section and, if placed above, a gas separator. If the seat short section is arranged at least 10 ft below the bottom of the fluid entry section, effective gas separation can occur in the annulus, where the casing acts as the outer cylinder of the separator. However, well conditions often do not allow the pump to be placed below the fluid inlet layer, consider using downhole gas separators. Conventional air separators consist of a fluid inlet section (such as a perforated section), an outer cylinder (such as a fuel pipe with a plug on the bottom) and a diptube at the bottom of the pump. 5, control the pump displacement What are the ways, can be controlled by adjusting the 4 parameters: plunger size, stroke length, pump stroke, daily running time. Due to the high cost of equipment, usually not to replace the wrong size pump. The easiest way is to change the configuration of the ground equipment, such as moving the beam to change the length of the ground and pump stroke; followed by the replacement of the motor pulley to control the pump number. Matching pump volumes with well productivity can be done by changing the daily run time. There are several devices that can be used to control run times: empty control, interval timer, and percentage timer. The air pump controller will stop the pump if it detects that the pump is not fully charged. Timer control pump running time, cheaper and easy to operate. This article is provided by Huangshan Aiken Machinery Manufacturing Co., Ltd.
The heat conversion rate of it is over 98% so the temperature rises fast. It can reach the set temperature in short time after being charged with electricity. Moreover, when the set temperature is reached, it will cut off the electricity automatically.
The temperature of the screen can maintain 80 degree so it is very safe for the customers. Besides,it is safe to children and pets.(Different sizes correspond to different power)
Ceiling Mounted Panel Heater,Ceiling Mounted Electric Panel Heater,Ceiling Mounted Heater,Wall Panel Infrared Heater
Shandong Dexiang Electrical Technology Co.,Ltd , http://www.heater-kerosene.com