The purpose of the decoration is not only for many people, but also for the beauty of the room, and more importantly, it is hoped to improve the existing space pattern of the room through the decoration to increase its use function. Therefore, more and more phenomena have been reconstructed during the renovation of the original building structure, mainly in the demolition of non-bearing walls. Then, isn't the load-bearing wall removable? Let's take a look at the related content of the home of the decoration home!
In the traditional concept of people, there has always been such a view: the load-bearing wall in the room cannot be demolished, but the non-bearing wall can be removed. This is actually a big mistake. In fact, not all non-bearing walls can be arbitrarily removed. The so-called non-bearing wall refers to the house consisting of a column frame of reinforced concrete. The floor is supported by a horizontal array, the array is supported by columns, and the columns are supported by the foundation. This structure is usually visible in the interior of the column. Most of the walls between the columns are filled with hollow bricks or ordinary bricks, which are generally non-bearing walls.
Many people believe that non-bearing walls are not heavy, but this is not the case. Because the non-bearing wall is a secondary load-bearing component relative to the load-bearing wall, it is also an extremely important support for the load-bearing wall. It must bear at least two parts of the load, and part of it is the weight of the wall. For example, in a six-story house, the non-load-bearing wall in the bottom house should bear the weight of the five-wall wall; the other part is structurally, the non-bearing wall usually It is also a seismic wall designed. That is to say, if an earthquake occurs, these non-load bearing walls will withstand the earthquake force together with the load-bearing wall. Therefore, for a certain family, it is not much problem to dismantle the non-bearing wall or make a hole in the wall. However, if the residents of the whole building are free to dismantle the non-bearing wall, the earthquake resistance of the building will be greatly reduced.
According to experts, the load-bearing walls of some rooms can be removed, such as lightweight material gypsum board for partition wall, CRC board and various metal and wooden partitions. The half-brick wall in the bathroom, if the support beam supporting the wall is designed in the floor structure, it can be removed, otherwise it cannot be removed. But be careful not to damage the waterproof layer, otherwise you will have to redo it. Although the brick wall connecting the balcony is not a load-bearing wall, it is generally thicker and has a certain bearing effect on the balcony, so it is best not to dismantle it, especially the old house. In other words, only half of the brick wall or light wall can be removed directly, otherwise it must be dismantled after the consent of the property department.
Removing the load-bearing wall may result in changes in water, heating, and electrical circuits, so these issues should be considered at design time. If the owner's decoration design has the intention of demolishing the wall, then the decoration company must submit the application to the property department before approval. Because the original design unit will leave a drawing for the property company when it is completed, the thickness and material of various walls such as load-bearing walls and non-load-bearing walls are clearly marked. According to the drawings, the property company can determine which walls can be dismantled and which walls cannot be removed.
The above is a detailed answer to the Xiaobian, I don't know if you are satisfied with the introduction of the decoration home network Xiaobian~ If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
It is not the consideration that the load-bearing wall can be dismantled and the non-bearing wall is removed.
PEEK (Poly Ether Ether Ketone) is a high performance engineering thermoplastic that offers chemical and water resistance similar to PPS, but can operate at higher temperatures. PEEK can be used continuously to 250°C and in hot water or steam without permanent loss in physical properties. For hostile environments, PEEK is a high strength alternative to fluoropolymers. PEEK carries a V-0 flammability rating and exhibits very low smoke and toxic gas emission when exposed to flame.
Peek Sheet,Peek Plate,Peek Plate Sheet,Peek Plastic Sheet
Ningbo Zero Engineering Plastics Co.,Ltd , https://www.zero-peek.com