Centrifugal pump packing seal maintenance methods are as follows: 1, cleaning packing box, and check the shaft surface for scratches, burrs and so on. Stuffing box should be clean, shaft surface should be smooth. 2, check the shaft runout, rotor unbalance should be within the allowable range, so as not to vibration is too large, unfavorable to the packing. 3, in the stuffing box and the shaft surface sealant or coated with a suitable lubricant. 4, the packaging of the roll of packing, first take the root and journal size the same stick, the filler wound on it, and then cut off the knife, the best knife was 45 ° bevel. 5, packing to be filled by root, not a few filling. The method is to take a filler, coated with a lubricant, hands holding each end of the filler port, opened along the axial direction, so that the spiral, and then from the incision into the journal. Do not pull along the radial direction to avoid misalignment of the interface. 6. Take a metal bushing with the same size material or lower shaft hardness as the stuffing box, push the packing into the deep part of the box, and apply a certain pressure to the bushing with the gland to pre-compress the packing. Pre-compression of 5% to 10%, up to 20%. Rotate the shaft a second time and remove the sleeve. 7, in the same way, filling the second root, third root. Note that when the filler is 4 to 8, the interface should be staggered by 90 ° when filling; the two filler should be staggered by 180 °; and the 3 ~ 6 should be staggered by 120 ° to prevent leakage through the interface. 8, the last packing filling, the application of gland compression, but the pressure should not be too large. At the same time by hand rotation axis, the assembly pressure tends to parabolic distribution. Then relax the lid a little. 9, run the test, if not sealed, and then squeeze some of the packing; if the heat is too large, relax it. This transfer was only droplet-like leaks and fever is not so far (the temperature of the filler site can only be higher than the ambient temperature 30 ~ 40 ℃), it can be formally put into use.
Phlizon Led Grow Light Promotion
Phlizon Full Spectrum LED Grow Light bar designed specifically for use as supplemental greenhouse lighting. This light is very similar to the much more expensive Fluence SPYDRx, in that they both use Samsung chips and 660nm red light .But Phlizon bar light costs about half as much and gives you more power.Also 3-5 years warranty.Safety FCC ETL Certified and IP54 Rated.Passive cooling,extrusion pure aluminum can 100% ensure heat dissipation. Plants will grow better under the Full Spectrum LED Grow Lights, as well their yield. will increase hugely.
Product Features
1. Samsung 5630 0.5w LM561b plus,LM561c, LM301b LED used, ultra high PPFD, replace HPS 600W and 1000W perfectly.
2. 400w with High PPFD at 5x5 feet coverage , have 553 umol/m2/s in 18 inch height from canopy.
3. Full spectrum LED added 660nm 1w/3w redLED, good for all growth stage, especially for flower stage, high yield: >2grams per watt .
4. Standard without dimming, dimming with different PPFD, Bluetooth wireless control system are optional.
5. Passive cooling (no fans),Aluminum material and heat-dissipation design.
6. Light distributed evenly in every spot and cover larger area
7. This LED Grow Lights consistently emit wavelengths in the range of 380 to 780nm.
8. Customizable spectrum ,any spectrum can be OEM/ODM,at any stage of growth accordingly
phlizon led grow lights,phlizon led grow light for sale, phlizon grow light"phlizon hot selling grow light"
Shenzhen Phlizon Technology Co.,Ltd. , https://www.szledaquariumlighting.com