Mahogany furniture is expensive and more expensive than ordinary furniture . It is often heard that it cannot be watered, sunbathed, or plastered with cotton and soft cloths. Is it trouble yourself? In fact, the maintenance of mahogany furniture is not so troublesome, as long as the furniture is not vandalized, basically without special care. Then in the daily maintenance and handling of mahogany furniture, pay attention to the following points:
One, daily maintenance1, because it is a full-wood structure, and the wood is very afraid of the nature of the dry, so the mahogany furniture on the home, there are great requirements on the location, the first step to be placed in the door, window, tuyere and other strong air flow position, The second step is to place the mahogany furniture in the heating furnace, fireplace, air-conditioning and other equipment straight to the place!
2, can not use chemical cleaners, alcohol, gasoline to wipe the stained mahogany furniture, because these so-called cleaners wipe off the furniture surface paint and paint gloss. It is most correct to gently wipe the stain with a natural maintenance agent such as natural walnut oil or beeswax.
3, mahogany furniture is generally used for a long time, so usually to protect the furniture surface coating, it is best every three months, wipe with a little wax, not only to increase the appearance of furniture, but also to protect the wood.
4. The service life of mahogany furniture is much longer than that of modern furniture. Therefore, the wax layer on the surface of mahogany furniture is usually protected. The best use period is to use beeswax once every three to four months to do a care, before doing care with a dry cotton cloth to gently wipe the dust on the furniture surface, to wipe along the wood, you can wipe several times more, Do not use force so as not to damage the surface of the furniture caused by dust, gravel, rubbing and beeswax. After 10-30 minutes, wipe the furniture with a clean, dry cloth and wipe the wax deep into the wood. Cycle maintenance can not only increase the beauty of mahogany furniture, but also protect the wood of mahogany furniture and prolong the service life of mahogany furniture!
5, Taiwan mahogany furniture panel, in order to protect the paint film is not scratched, but also to show the wood texture, generally placed on the table thick glass plate, and between the glass plate and the wooden table with a small suction pad to separate. It is recommended not to use transparent polyethylene crystal plate.
6. The essential oils used to maintain furniture are only suitable for furniture that is not painted and treated by waxing. Use frequency should not be too high, under normal circumstances, 2 to 3 months can be used once, in a relatively dry environment can properly shorten the maintenance interval, a month or so maintenance. It should also be reminded that although essential oils can be "dried," they must always be used in the usual manner. The oils have the property of vacuuming. Too large amounts of dust can cause dust to adhere and produce a greasy feeling.
1. The furniture net editor recommends that when moving the furniture, the objects inside the cabinet should be removed and the doors and drawers should be closed to prevent the furniture from leaning and parts from falling and hurting people. Don't push hard and push it when moving so as not to loosen and break the foot plate and hoe.
2. The furniture made of precious wood is very heavy and brittle. When one person moves, it is easy for one side to touch the ground first, and the heavy weight is momentarily added to one leg, causing the furniture to be damaged. Therefore, it is better to have two or four people move at the same time and place them at the same time so as to avoid crashing and smashing.
3, move the chair can not move the handrail, two hands should be placed under the chair, because the arm of the handrail is more fragile, so as not to damage. You can't move your back legs (above) because the hind legs are thin and must stand the weight of the entire chair, which is easily damaged.
4, move the table can not move the fragile carved parts, it is best to face down to move and stack, in order to reduce its center of gravity. When moving, both hands should be placed on the front and rear teeth plates, and must not be placed on the head plates at both ends. Because the headboard in the furniture is a weak part, it is connected to the dental plate with only a small pimple.
5, the cabinet must be sold on the pin pin, the drawer is locked, it is best to use the rope first "play", tied on two laps to protect the furniture cabinet doors and drawers, so as not to tilt in the handling process to throw it out ,break. People who move cabinets should stand on both sides of the building. People on one side should put the top of the cabinet and people on the other side should carry cabinets to make the cabinet roll, with a 45-degree angle to the ground. This is more labor-saving and safer. It is an internal law mover.
6. Moving bed should first remove the screens, shelves and other components on the bedside, place it on the bed surface, and then move it after binding; when installing, use the structure of the concrete to align it and insert it.
Must pay attention to the handling process, such as chairs, tables, etc. can not lift the handle, can not squatting, must hold the bottom, like the screen and other glass, in the packaging must be marked clearly, fragile, upward notes, etc. This general release can not be placed flat, erect or horizontal.
When we move any furniture, we must be careful in the process of moving, and use air bubble paper to wrap the easily colliding places or corners, effectively reducing the damage caused by the collision. The above is the packaging method of Kunming Moving Company. And where care should be taken during handling.
The above is the Suzhou Furniture City on [home science | mahogany furniture maintenance and handling methods] explained in detail, this article collected by GO Jiaju Xiaobian on the Internet does not represent the point of view of this site, if you still want to learn more about the furniture brand Article, please continue to review the [Furniture Sharing Shopping Guide] related articles, please pay attention to the GO good home site.
Table Plasma Cutting Machine features:
1. Table Plasma Cutting Machine with welded lathe bed of thick profiled steel, more solid and stable.
2. Perfect lathe table design, 8mm steel plates fixed on lathe table covered by cast sheath.
3. Advanced material inclined discharging design.
4. Table plasma Cutting Machine support FASTCAM nesting software such as the standard G code path generated file can also be read by software conversion software such as AUTOCAD generated DXF formats. U disk exchange control system processing files, easy to operate.
5. Table plasma cutting machine support CAMDUCT software professional for air duct industry.
Table Plasma Cutting Machine
Plasma Cutter For Stainless Steel,Cnc Steel Cutting,Ss Cutting Machine,Ss Plate Cutting
Jinan Huaxia Machinery Equipment CO.,Ltd , https://www.cnformingmachine.com