Wood flooring is the commonly used decorative material in the current home and public building decoration. As its sales volume soared, complaints also showed an upward trend. Therefore, when home decoration, you must carefully check the quality of the floor decoration, do a good job acceptance.
Shuaibang Design     Tong Ji . Yu Run
Floor acceptance Yang standard
1, see the color of the floor is the same. If the color difference is too large, directly affect the appearance, you can ask for exchange; if the color is too consistent, almost no color, it depends on the floor surface pattern is the same. If the pattern is almost the same, it may be craft wood floor, not the material floor of the so-called precious wood species. Now some flooring material suppliers use ordinary wood flooring materials, but in the surface paste a layer of valuable wood veneer to shoddy, said to be moisture-proof, in fact, is afraid of being seen opposite the pattern and the front of the inconsistencies .
2. Check whether there is noise on the floor. When passing the inspection, walk on the floor and step up. Steps must be increased. In particular, check the acceptance of the wall and the door hole. Find the location with noise, and repeat the walk to determine the specific location of the sound. Good mark. In this case, you can ask to remove the resurfacing. The site where there are sounds is caused by non-standard operations and unqualified materials used by construction workers during the construction process. The operation is not standardized, mainly reflected in the fixed keel is not solid; material failure is mainly reflected in the ground keel without drying. Some renovation construction units use undried keel construction. The surface shows signs of drying. In fact, they did not dry. The keel with high moisture content will shrink in volume during the natural drying of the wood, causing looseness.
3, acceptance of the floor deformation, warping, acceptance method is to use 2 meters long ruler, leaning on the floor, the flatness should not exceed 3 mm. More than a few measurements, if the passing rate of 80% or more is considered qualified, and vice versa, is unqualified. Sometimes we find that the floor is partially arched: if it is a solid wood floor, it is because it is too tight or the floor is too dry (water content is too low); if it is a laminate floor, it is a poor quality floor. Therefore, the arching of the floor is a serious quality problem.
4, the acceptance of the baseboard: baseboard and door frame clearance ≤ 2 mm; skirting line spacing between stitches ≤ 1 mm; baseboard and floor surface clearance should be in the range of 3 mm to 5 mm; kicking The height difference of the buckle should be ≤ 1mm.
5. Acceptance of the door clasp: The door clasp should be installed directly under the door. It is advisable to close the door both inside and outside. The gap between the clasp and the door is between 3 mm and 7 mm. The door can open. Closed and comfortable. The buckle should be installed firmly and stably. You can kick the middle part of the buckle to check if the sides of the buckle are tilted or loose and there is no abnormal sound.
6, the final acceptance of the floor surface is a blink, cracks, scratches. Commonly due to the untreated keel, there are locusts inside. When it was found that there was a blink, the floor was already almost cracked; gaps and scratches were known at a glance. Regulations: floor gap should not be greater than 0.5 mm; scratches are mainly due to rough decoration, such as waxing method can not be repaired, it must be exchanged.
The materials and grades of wood flooring are in line with the design requirements. The moisture content should be about 10%. The keel and studs should be treated for anti-corrosion treatment. The wooden keel should be firmly and flatly installed, and the spacing and fixing method should meet the specification requirements. Solid, no loose, firm paste, no empty drum, the use of plastic varieties meet the specification requirements.
Visually inspect the surface of the wooden floor for planing, grinding, no scars, russia and burrs, with clear patterns, uniform color on the surface of the clean oil, proper paving direction, tight seams on the surface layer, staggered joint locations, and clean surfaces. The skirting boards have tight joints, smooth surfaces, and a uniform height and wall thickness. Checked with a 2-meter ruler, the ground flatness error is less than 1 mm, the gap width is less than 0.3 mm, the mouth plate straightness error is less than 3 mm, and the seam straightness error is less than 2 mm.
Construction Acceptance Flooring Nature Flooring Decoration Design Home Decoration Decoration Home Decoration Home
Rubber Cable Protector,Dual Cable Cross,Rubber Cable Protector,Yellow Jacket Cable Protector
Road Separator Co., Ltd. , http://www.911signaleurope.de