[
Pacific Security Network News ]
When we are using fiber optic transceivers, we will inevitably encounter some problems. How do we solve these common problems? Let me introduce you below.
1, Power light is not bright
electricity failure.
2, the Link light is not bright
The fault may be as follows:
Check if the fiber line is open.
Check if the fiber line loss is too large and exceed the receiving range of the device.
Check that the fiber interface is properly connected, the local TX is connected to the remote RX, and the remote TX is connected to the local RX.
Check whether the fiber connector is properly inserted into the device interface, whether the jumper type matches the device interface, whether the device type matches the fiber, and whether the device transmission length matches the distance.
3, the circuit Link light is not bright
The fault may be as follows:
Check if the network cable is open.
Check whether the connection type matches: devices such as network cards and routers use cross-lines, switches, hubs, etc., using straight-through lines.
Check if the device transfer rate matches.
4. The network packet loss is serious: The possible faults are as follows:
The electrical port of the transceiver is interfaced with the network device, or the duplex mode of the interface of the two devices does not match.
Twisted pair and RJ-45 head have problems and are tested.
Fiber connection problem, whether the jumper is aligned with the device interface, whether the pigtail matches the jumper and coupler type.
Whether the fiber line loss exceeds the device acceptance sensitivity.
5, the fiber transceiver can not communicate after the two ends are connected
The fiber is reversed, and the fiber connected to TX and RX is reversed.
The RJ45 interface is not properly connected to the external device (note that the straight through and the spliced) fiber interface (ceramic ferrule) does not match. This fault is mainly reflected in the 100M transceiver with photoelectric mutual control function, such as the APC ferrule The transceiver of the PC ferrule will not be able to communicate normally, but the non-optical mutual control transceiver will have no effect.
6, time pass and time phenomenon:
It may be that the optical path attenuation is too large. At this time, the optical power of the receiving end can be measured by the optical power meter. If it is near the receiving sensitivity range, the optical path fault can be basically judged within the range of 1~2dB.
The switch connected to the transceiver may be faulty. In this case, the switch is replaced by a PC, that is, the two transceivers are directly connected to the PC, and the two ends are connected to PING. If the switch is not present, the switch may be basically faulty.
It may be a transceiver failure. In this case, connect the transceiver to the PC at both ends (not through the switch). After both ends have no problem with PING, transfer a large file (100M) from one end to the other end to observe its speed. If the speed is very slow (files of less than 200M are transmitted for more than 15 minutes), the transceiver can be basically judged to be faulty.
7, after a period of communication, the crash, that is, can not communicate, resume normal after restarting
This phenomenon is generally caused by the switch. The switch performs CRC error detection and length check on all received data. It checks that the packet with the error will be discarded and the correct packet will be forwarded. However, some packets with errors in this process are not detected in the CRC error detection and length check. Such packets will not be sent during the forwarding process and will not be discarded. They will be accumulated in the dynamic cache. (buffer), can never be sent out, wait until the buffer is full, it will cause the switch to crash. Because restarting the transceiver or restarting the switch at this time can restore the communication to normal, the user usually thinks it is a problem with the transceiver.
Flange is a method of connecting pipes valves, pumps and other equipment to form a piping system.Application: oil,
chemical industry, water conservancy,electric power, boiler, machinery, metallurgy,sanitary, construction etc.
Blind Flange
A blind flange is a round plate which has all of the relevant blowholes except center hole, and because of this feature the blind flange is usually used to close off the ends of a piping systems and pressure vessel openings. It also permits easy access to the interior of a line or vessel once it has been sealed and must be reopened.
Without the blind flange it would be difficult to perform maintenance or repairs on a pipeline. The flow would need to be s
hut off at the nearest valve, which could be miles away from the repair area. Valves are also very expensive and are prone to sticking. The blind flange is a much more cost efficient way of sealing a pipe.
Blind Flanges are commonly used in petrochemical, pipe engineering, public services and water treatment etc.
|
Flanges Types
|
|
Slip On Flange ,Welding Neck Flange ,blind flange ,plate flange ,socket welding flange ,
|
|
long welding neck flange ,orifice flange ,loose plate flange
|
|
Materials
|
|
carbon steel :ASTM A105 ,A694.A36,Rst37.2,C22.8,SA350 LF2/LF1,Q235,Q345,etc
|
|
stainless steel :304,304L,316,316L,A182,etc
|
|
alloy steel :ASTMA182,F11,F12,F60,F22,etc
|
|
Marking type
|
|
forged or forging
|
|
Standard
|
|
ANSI B16.5/B16.47/B16.48/B16.36,ASME ,MSS SP44,API ,AWWA
|
|
DIN2527,DIN2566,DIN2573,DIN2576,DIN2641,DIN2642,DIN2655,DIN2627,DIN2628,DIN2631,DIN2632,DIN2633
|
|
DIN2634,DIN2635,DIN2636,DIN2637,DIN2638,DIN2673
|
|
BS4504/10
|
|
Pressure grade
|
|
ANSI B16.5 B150Lbs, 300Lbs, 600Lbs, 900Lbs, 1500Lbs, 2500Lbs
|
|
BS4504:PN2.5,PN6,PN10,PN16,PN20,PN25,PN40,PN63,PN100,PN160
|
|
JIS:5K,10K,16K,20K,30K,40k,63k
|
|
Facing
|
|
|
|
|
|
|
|
|
|
|
|
RF/M/FM/G/T/RJ
|
|
|
|
|
|
|
|
|
|
|
Blind Flange
Blind Flange,Steel Blind Flange,Forged Blind Flange,Stainless Steel Blind Flange
Shijiazhuang Huize Pipe Fitting Co., Ltd. , https://www.huizegd.com